What is the job of a Plant Commissioning Engineer?
The job of a plant commissioning engineer consists of getting a newly built or expanded industrial facility from being finished on site to running safely and steadily. The plants can be chemical, petrochemical, water treatment, food or energy plants, among others. It is a position usually reached from a related engineering degree, and its aim is to check that every piece of equipment and every system does what the design says before continuous production begins.
A typical day mixes office and plant. In the morning, the drawings, the lists of pending tests and the day's work permits are reviewed. Then the installation is walked through with the assembly, instrumentation and operations staff to check valves, pumps, pipes, sensors and control panels. Tests are done in stages, the faults found are noted, their repair is coordinated and the results are recorded in documents that are later handed to the client. Meetings are frequent to decide what is tested and in what order.
Typical tasks
- Preparing the procedures and checklists used to test each system in the plant.
- Checking that the installed equipment matches the drawings and the design specifications.
- Coordinating tests with water, air or inert gases before the real process materials are introduced.
- Recording the faults and open items that appear and following up on their correction.
- Taking part in the gradual start-up of the plant together with the operations team.
- Writing the reports and the final documentation handed over to the plant owner.
- Explaining to the operations staff how each system works and what to do when an alarm goes off.
Subjects and content usually covered
- Mass and energy balances, and thermodynamics.
- Unit operations: pumping, heat exchange, distillation, reaction and separation.
- Instrumentation and process control.
- Electricity and the basics of industrial electrical systems.
- Reading piping and instrumentation diagrams and plant drawings.
- Process safety, risk analysis and industrial safety standards.
- Project management and quality of documentation.
Usual duration and type of training
Because this is a job and not a degree in itself, there is no single length. The usual route is a related engineering degree, such as chemical, process, mechanical, electrical or instrumentation engineering, which typically takes 4 to 6 years depending on the country. After that, people usually add some time of experience on a construction site or in plant operation, often 1 to 3 years, along with short courses in safety, instrumentation or project management, lasting from a few weeks to a few months. University engineering study is in person in many places, and the timing varies from one country to another.
How you get there and what is usually required to practice
The most common paths start from a related engineering degree, above all chemical or process engineering, although people also arrive from mechanical, electrical or control engineering. Many begin as a junior engineer at a construction company, at an engineering contractor or in the operations area of a plant, and gradually take on larger tests and systems.
In many countries an engineering degree is enough for this job, although a professional registration is sometimes required to sign documents. Safety courses for working in industrial plants are also usually required, such as work in confined spaces, work at height or handling hazardous substances. A second language, often English, is usually useful because projects and equipment suppliers are often international. Getting the first position can take time, because companies value previous experience on site.
Skills that help
- Reading drawings and process diagrams and relating them to what is seen in the installation.
- Planning the order of the tests so that each system is ready when it is needed.
- Tracing the cause of a fault by separating what is mechanical, what is electrical and what is control.
- Communicating clearly with installers, operators, suppliers and clients.
- Following safety procedures and work permits rigorously.
- Documenting precisely what was tested, what is pending and what was corrected.
Career paths and job opportunities
- Engineering and construction companies that build industrial plants.
- Chemical and petrochemical plants and refineries during new projects or expansions.
- Water and wastewater treatment plants.
- Food, beverage and pharmaceutical industries installing new lines.
- Equipment manufacturers that send staff to start up their machines.
- Technical consulting companies that support project owners.
What you are not always told
- The work is usually tied to projects, so people travel or live for periods near the site, sometimes in remote areas.
- Hours stretch as a start-up date gets close, and can include nights and weekends.
- The work happens on a site with dust, noise, heat or cold, wearing a helmet and protective equipment for much of the day.
- There is pressure over deadlines and costs, while safety is not negotiable, which creates tension.
- When a project ends, the work moves elsewhere, so stability depends on going from one project to the next.
How the field is changing
Drawings and test documents are moving from paper to digital platforms, and three-dimensional models and simulations are used to review systems before they are tested in the field. Some control tests are run on a virtual version of the plant, which makes it possible to find programming errors before start-up. Safety and environmental requirements are also growing, and more sensors and automatic systems are being installed, so this work calls for more and more knowledge of control and data.
Want to know if this is the right career for you?
Take the free vocational test with 5 scientific methods — CHASIDE, Holland, Big Five, MMMG and VAK — to get your personalized profile. You can also explore all university careers or learn about the scientific methodology.